Description:72-2110RK-02 – Beacon 110/ Single channel controller with small red light (no sensor)

Features

• Low cost versatile solution
• Compact, weatherproof, NEMA 4X enclosure
• 115/220 VAC or 24 VDC operation
• Long life sensors (2+ years typical)
• Accepts RKI LEL/O2/H2S/CO direct connect sensors
• Accepts any 4-20 mA transmitter
• Audible alarm with reset button
• Two programmable alarm levels
• Built-in trouble alarm with relay
• Relay rating 10 amps, form C
• Provides 4-20 mA output

Description

Gas detection should not be complicated. The Beacon 110 is gas detection simplified.

The Beacon 110 is a powerful, low cost fixed system controller for one point of gas detection. It is microprocessor controlled, versatile, simple to install and operate, and priced to be the industrys best value single gas detection controller. It is capable of accepting RKI sensors directly for LEL level combustibles, Oxygen, Hydrogen Sulfide, or Carbon Monoxide. The Beacon 110 can also accept any 4-20 mA transmitter (2 or 3 wire, 24 VDC). Sensors can be mounted directly at the Beacon 110 housing, or can be wired remote from the controller.

The 10 amp rated relays are strong enough to directly power external alarms and horns. The digital display has backlighting and simultaneous readout of the gas type and concentration.

The Beacon 110 is also housed in a NEMA 4X rated case for a weather tight seal. This case design complies with lock out / tag out standards and can be fully secured. An external reset switch allows the alarm to be silenced from outside of the controller housing. The Beacon 110 ships complete with a wall mounting kit for easy installation.

RKI offers the industrys widest selection of standard and toxic gas detection sensors, which can be utilized with the Beacon 110, providing gas monitoring protection for almost any application.

Specifications

Physical

Dimensions Height: 8.5 216 mm
Width 7.0 178 mm
Depth 4.3 109 mm Enclosure Wall mounting grey polycarbonate with hinged cover. Conduit
Connection
3/4 NPT conduit hubs, 2 provided.
1 for sensor wiring
1 for power & relay wiring Wiring
Termination
Screw type terminal block 14 gauge max. Power Universal 115 VAC & 220 VAC, or 24 VDC nominal, battery backup option available Controls 3 internal push buttons for setup, programming, and calibration. 1 external push button for alarm reset

Environmental

Operating Temp -4F to 122F (-20C to 50C) Storage Temp -4F to 158F (-20C to 70C) Relative
Humidity 0 100% RH Enclosure
Rating NEMA-4X enclosure, waterproof, chemical, and weather resistant.

Inputs

Direct Wired
Sensors LEL
Oxygen
Carbon Monoxide
Hydrogen Sulfide
Remote amp not required for less than 500 feet. 4-20 mA Sensors Accepts any 4-20 mA transmitter (24 VDC, 2 or 3 wire). A wide variety of RKI/Riken sensors are available with 4-20 mA signals. (See list of detectable gases.) Wiring distances up to 5000 feet Sampling Methods Diffusion and sample draw heads available.

Outputs

Relays 3 relays 10 amp rating (at 115 VAC), SPDT isolated contacts. 2 relays for gas alarms and 1 trouble relay. Relays fully programmable for: increasing or decreasing alarm, latching or self reset, normally energized or normally de-energized, time delay for alarm on and alarm off 4-20 mA Signal output, 4-20 mA (maximum load impedance 500 ohms), per channel 24 VDC 24 VDC (400 mA max) output provided to operate sample drawing adapters or other accessories Display 2 x 8 Alphanumeric display with backlighting. Audible Built-in audible alarm, 94 dB, mounted on enclosure
Coded output: pulsing = gas alarm, steady = fail Visual 3 LEDs on the front cover for alarm status indication, and malfunction

Warranty

One year materials and workmanship Partial List Of Detectable Gases
Many other gases or ranges available. Contact RKI for gases or ranges not listed. Ammonia (NH₃) 0 75.0 ppm Arsine (AsH₃ ) 0 0.20 ppm Boron Trichloride (BCl₃) 0 15.0 ppm Carbon Dioxide (CO₂) 0 1.0 % Carbon Monoxide (CO) 0 300 ppm Chlorine (Cl₂) 0 3.0 ppm Chlorine Dioxide (ClO₂) 0 1.00 ppm Chlorine Trifluoride (ClF₃) 0 1.00 ppm Combustibles 0 -100% LEL Diborane (B₂H₆) 0 30.0 ppm Fluorine (F₂) 0 6.0 ppm Hydrogen (H₂) 0 2000 ppm Hydrogen Chloride (HCl) 0 15.0 ppm Hydrogen Fluoride (HF) 0 9.0 ppm Hydrogen Sulfide (H₂S) 0 -100.0 ppm Nitric Oxide (NO) 0 -100.0 ppm Nitrogen Dioxide (NO₂) 0 15.0 ppm Nitrogen Trifluoride (NF₃) 0 30.0 ppm Oxygen (O₂) 0 25.0 % Ozone (O₃) 0 1.0 ppm Phosphine (PH₃) 0 1.0 ppm Silane (SiH₄) 0 15.0 ppm Sulfur Dioxide (SO₂) 0 30.0 ppm TEOS (Si(OC₂H₅)₄) 0 -15/30 ppm

Specifications subject to change without notice.
Made in the USA